List Categories | List All Articles | List Articles By Title
Used But Not Used Up
Some DIY Maintence will put Used tools back in Main Stream Operation:
Professional grade tools are made to withstand long hours of use and abuse. Many home shops have a number of Professional grad tools but for the most part most home shops have tools that are some what less in quality.
No matter what grade of tool you have none of them are made to be the "last tool you will have to buy".
What is nice is that for the most part the average grade as well as the professional grade tools are designed and built to be reparied which will translate into many years of service.
For the home shop items such as pads, electric cords, on/off switches and motor brushes can be easily replace and done so without a huge pinch in the pocketbook.
A lot of these repairs can be done without even taking the housing off the tool. So to extend your tools service life and get the most from it lets examine a few things you can do.
Always remember SAFETY FIRST:
The first thing before anything else is done is always remove the power source. Make sure that the tool is unpluged or if it is cordless remove the battery. Do this before you pick up any other tool.
If you are going to have to unassemble any part of the tool you need to remember that you will at some point have to put it back together.
When I start to take something apart I get a shallow cardboard box to lay the parts in so that I can keep them seperated and organized. This will make reassembly go much smoother. Watch for different lengths of screws and bolts. A perfectly good tool can be ruined because you try to put the wrong screw back in and strip out a thread.
The number one power tool killer is HEAT. If you want your tools to last you have to keep them running cool. Any motor by its very nature has armature windings, gears, and bearings that turn at high rates of speed. A natural law says that with any action there is an equal and opposite reaction. So if while your power tool preforms a certain operation the opposite reaction is that it will create heat. If your tools are so hot that they are uncomfortable to hold in your bare hands then its time to do something or the end is near.
Remember a Cool Tool is a Good Tool.
So what is the best way to maintain a Cool Tool?
Keep it clean. Any tool expert will always tell you that keeping dust and dirt from gathering around the motor of a power tool is one of the most important factors of long tool life. All your tools that use universal motors have air intake slots so that air can be sucked through with a fan. A natural byproduct of woodworking is dust and that dust will get sucked into these intake slots. Besides these intake slots every tool has plenty of other nooks and crannies that will grab that dust and hold it.
If your shop is equiped with an air compressor then daily cleaning will be a snap. Make sure you know which slots on your tools are intake and which are exhaust then while it is running shoot a nice refreshing jet of compressed air into the intake side and watch that ole dirt and dust go flying.
If you are not so lucky as to have compressed air then the maintaince is a little more difficult but just as important. You will need to take the housing of the tool off and manually clean the air intakes with a clean brush. If dust and dirt are caked onto the fan blades it will be necessary to remove that also. Just make sure you use something that can not scratch the surface of the blade so as not to upset the blade balance.
Just this one simple maintance procedure will put many extra hours of use into your tools.
Motor Brush Replacement
I have a Craftsman 3/8" electric drill that was one of the first power tools that I ever could say was mine. My father gave it to me when I left home after graduating from High School. This drill and I have been through some times. I used it and to be honest abused it quite a bit.
Finally one day I need it for somthing I was working on and when I got it pluged up and pulled the trigger, nothing happened. I checked the power supply, and all of the other things like wiggling the cord with no results. Then I happened to grab the chuck and kind of twist it a little and since ole dummy me had the trigger squeezed all at once the thing took off and tried to take my fingers along with it.
This brings me to a simple DIY operation that if done on a regular basis will avoid those skin burns that I got.
Check and Change the motor burshes.
If your tool wont start up without a little help from you or you see a lot of sparks flying around the motor housing ( a little sparking is ok just not more than 1/4") or if that motor just doesn't sound or feel right it could be the brushes need replaced.
Now saying the brushes need replaced might have you going off looking for brushes, which you will never find. What you will really find that everyone calls brushes are small blocks of hard graphite with little springs attached to them.
Accessing the brushes is easier on some tools than others. You may have to remove the tool housing or you might be able to access the brush cover from outside the housing.
By whatever method you need to acces the brushes once you have removed the covers the tension on the small springs will be released and they will jump out at you. Gently pull on the springs and the brushes will slide out. The brush will be curved to fit the curvature of the rotating armature. In most instances if it is less than 1/4 inch from the bottom of the curve to the bottom of the brush it should be replaced. If your owners manual is available you may want to check to see of they have a different specification. You will want to remove and measure both brushes as they will not always wear at the same rate.
If new brushes are called for then you have a couple of options. The first and best is to replace with the manufacturer's replacements. If that is not an option then generic brushes are available and will do an adaquate job.
Many times new brush ends are flat but they will conform to the shape of your armature in a short time. "Seat" the new brushes by running your tool with no load for a while.
Brushes are not expensive and will make that old tool run smoother and last longer.
That old Craftsman drill that I told you about. I still have it and have replaced the brushes several times. By the way it was new in the 60's.
Here is still another common problem with power tools and it is not that hard to fix.
With the newer tools that have variable speed triggers if they get worn you may go from variable to just one or even no speeds. Could be a defective switch.
Now I am sure that all of you are organized and when you get a new tool you safely file that owners manual away for future reference after you finish reading it. So you now need to go to the archives and find that manual for the particular tool you are having problems with and get the part number for the problem switch. Now you can easily order a new replacement from the manufacturer. Get the cost and compare and decide if it is worth replacing before you order.
If it is and you have that new switch in hand you will need to get inside the tool housing. Once in there get yourself a pencil and paper and do a simple drawing of the switch and wires. Note the position and colors and look at the new switch to make sure the wire colors and positions are the same. Remove one wire from the old switch and attach the comparable wire from the new switch. Do these one at a time until all of the wires have been attached. Position the switch and make sure it operates smoothly before reassembling the housing and hooking up the juice.
Along with replacing switches and in the same vein of maintance is power cord replacement.
It is a good idea to inspect your power cords on a regular basis and look for things like fraying, missing grounding pin or the cord pulling out of the tool housing. Any of these conditions can pose a shock hazard or short circuit your tool.
Again the best course of action is to obtain a replacement from the manufacturer.
One you have done that it's time to open up the housing again and compare the wires on the old cord with the ones on the new. If they are not the same before you continue you need to contact the manufacturer. If the "hot" and "neutral" wires are switched it is sometimes possible to damage a motor. This is know as reversing the polarity and it is better to check before you burn your motor up.
If everything is ok a simple way to keep track of everything is to cut the old cord off about 4 or 5 inches from the terminals. Slide the new cord into place. Remove one old wire and replace with the corrosponding new one and continue until all of the wires have been replace. Following a simple system like this will eliminate any chance of hooking up a wire in the wrong place.
In conclusion by doing some of these easy and inexpensive routine maintenance procedures you can take a good used tool and keep it from being used up.
Always keep safety in mind and have fun with your woodworking projects.
About The Author
Gene Miller is the Owner and Webmaster of www.woodworkingtoday.com. His amateur woodworking experience started as a young teenager when he designed, built and raced several Soap Box Derby cars. Later he assisted his father in remodeling several rooms in their home. Through the years he has tackled many woodworking and Home Improvement projects. With each project he has added to his information of tools, tips and methods.
How To Buy A Conservatory In The UK
The first question is, what is a conservatory?There is no standard definition of what constitutes a conservatory (apart from "greenhouse"). This is one reason why quotes vary so widely.
The Bathroom - The Forgotten Area Of Your Home?
The bathroom in your home is the one room that has undergone a complete transformation in the past several years. A transformation that is as far as how it is defined.
Measuring For Your Vinyl Replacement Windows
Let's say you're tired of those old wood windows, and you decide it's time to upgrade to vinyl replacement windows. You get 2 or 3 contractors to come out and give you an estimate.
At Last You Can Customize Your Pegboard As Much As You Want
Customizable metal pegboard is set to revolutionise utensil storage. For forty years the limitations of fibreboard has narrowed our imagination in utensil storage.
Ceiling Fans - That Dont Require The Ceiling
The trend in remodeling homes is to expand the outdoor backyard or patio into a lovely room where you can entertain. It just makes sense to extend your surroundings to be more useful.
To Picket Fences
Of the 359 homeowners in my area, 112 are running afoul of the law in a deviously blatant way by committing the heinous "fence offence;" in other words, breaching Los Angeles municipal code sections 12.21 and 12.
Avoiding Leaks When Installing Vinyl Retrofit Windows
These days a lot of homeowners are replacing their old windows with vinyl windows using the retrofit style of window frame. This is particularly true in the west, and specifically, in California.
Selecting the Right Air Compressor for Your Air Tool
An air compressor is used to power air tools such as spray guns, air sanders, air wrenches, air hammers, and much more. While not as widely used, air tools are more powerful than traditional electric power tools.
10 Tips for Working With a Contractor
This is the year you're going all out. You're going to build a deck, add a porch, erect a gazebo or lay a patio.
Brighten Up Your Shelves With Picture Frames
Would you like to add a personal touch to your home or office, but not sure how? Picture frames may be your answer. Picture frames are a fun and simple way to add color, character and style.
Tips and Suggestions To Help You Plan and Build Your Own Log Home
Log Cabin Homes: They have come a long way. Here are some tips and suggestions to help you plan and build your own.
Is It Time For Solar Energy to Get Hot?
Solar energy has been around for quite a while and most people don't think about it much except for the ones who are already into renewable sources of energy. Environmentalists have always loved the idea of solar energy but what has kept it from going more mainstream, being more widely used and looked upon as something someone wants to spend money to install on their property? There have been improvements in the technology of solar energy, but has there been enough? Isn't the war on terror and the desire to be independent of foreign energy sources enough to persuade people to use solar energy? At what point will solar energy become the great and never ending source of energy many of envisioned many years ago?Well, I, for one, think that the time has just about come for solar energy to really take off because of one reason: it will be economically the right and smart thing to do.
Remodeling Your Kitchen Cabinets
While remodeling your kitchen, install only the essential cabinets, so you can spend on quality rather than quantity. Look for durability, and specify plywood panels rather than particleboard.
An Overview of Aluminium, Plastic and Timber Conservatories
Conservatories remain a popular accoutrement and attachment to homes throughout the United Kingdom and the world in the 21st century. Around for over three hundred years, conservatories work to provide a lovely transition between the main residence and the natural surroundings abutting the home.
What Two Words Will Double the Space in Your Home?
Just two words and a bit of explanation about them will help you to double, maybe even triple, the space in your home now. Those two words are "Go vertical.
Laminate Flooring Basics
Laminate flooring resembles the look of hardwoods but offers easier installation and stronger durability. You can use laminate flooring in any room in the house, including hallways, foyers and family spaces, bathrooms, and kitchens.
Laminate Flooring Is Attractive And Long Lasting
Laminate flooring is perfect for people who want to install a floor covering that is easy to install and combines the rich look of hardwood with the easy care of a laminate counter top. Laminate floors that have been constantly gaining popularity since their creation a few years ago.
Candle Making 101
If you'd like to try your hand at candle making, set aside two hours one day next weekend, and start with an easy project, using your old candles to test the waters. If it's instant gratification you crave, you'll see the fruits of your labor in just a couple of hours with a minimum expenditure for supplies.
Thinking of Remodeling Your Kitchen?
If you like to cook, or even if you just do it from necessity, having a homely, organized, and modern kitchen is probably important to you. Although, the traditionally kitchens are still out there, there are so many new, modern elements that can add luxury and class and convenience to any home.
Light Up Your Kitchen with the Right Lighting!
The proper lighting in a room can make or break it. With lighting, you can create a soft, cozy room for reading and relaxing.
home | site map
All articles are copyright to their owners.
Note: this website lists articles, We do not Write Articles !